ISO INTERNATIONAL STANDARD 11148-13 First edition 2017-11 Hand-held non-electricpowertools- Safetyrequirements- Part 13: Fastener driving tools Machinesportativesamoteurnon électrique-Exigencesde securite- Partie13:Machinesaenfoncerlesfixations Reference number ISO11148-13:2017(E) Tso @ISO2017 Copyright Inte Not for Resale, 12/01/201700:51:46 MST IS011148-13:2017(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Ch.de Blandonnet 8·CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 0111 Fax +41 22 749 09 47 [email protected] www.iso.org IS0 2017- All rights reserved Not for Resale, 12/01/2017 00:51:46 MST IS011148-13:2017(E) Contents Page Foreword .V Introduction. ..vi 1 Scope. .1 2 Normativereferences .1 3 Terms and definitions 2 .2 3.1 General terms. 3.2 Termsand definitions relatedtofastenerdrivingtools .3 4 Safetyrequirementsand measures 8 4.1 General 8 4.2 Mechanical safety. 8 4.2.1 Protectionagainstpointsandedgesoffasteners 8 4.2.2 Preventionofunintended ejection offasteners 8 4.2.3 Preventionoffreeflightoffasteners 9 4.2.4 Designoftheworkpiececontact 4.2.5 Permittedtriggeractuationmodes. 11 4.2.6 Strength ofthefastener driving tool 12 4.2.7 Surfaces, edges and corners. 12 4.2.8 Stability 12 4.2.9 Tool construction. 12 4.2.10 Unintentional changeofactuationmode 12 4.3 Electrical safety 13 4.4 Thermal safety. 13 4.4.1 Hotsurfaces 13 4.4.2 Coldsurfaces 13 4.5 Noisereduction 13 4.6 Mechanical impact (vibration/recoil) 13 4.7 Materials and substancesprocessed,used oremitted 14 4.7.1 Collating material residues. 14 4.7.2 Discharged air, gas and lubricants 14 4.8 Ergonomics 14 4.8.1 Weight and control ofthetool 14 4.8.2 Handledesign 15 4.9 Userinformation 15 4.9.1 Tool markings 15 4.9.2 Tool operatinginstructions 15 4.10 Fireand explosion 15 4.10.1 Hazardousenergysuppliesforpneumatictools 15 4.10.2 Releaseofflammablegasfromgastoolsandgascontainers. 15 4.10.3 Ruptureduetohightemperatures in thetool. 16 5 Verification .16 5.1 General 16 5.2 Protectionagainstmechanicalhazards 16 5.2.1 Protectionagainstpointsandedgesoffasteners 16 5.2.2 Preventionofejectedfasteners. 16 5.2.3 Preventionoffreeflightoffasteners 17 5.2.4 .17 Designof theworkpiececontact. 5.2.5 Actuationmodes. 18 5.2.6 Strength of thefastener drivingtool 20 5.2.7 Surfaces,edges and corners. 21 5.2.8 21 Stability 5.2.9 Tool construction. .21 Unintentional changeofactuationmode. .21 5.2.10 Cyrtnemaonlrightsrserved ili ided by IHS Markit underlicense withANSI ted without license from IHS Not for Resale, 12/01/2017 00:51:46 MST